How do you cut laminate countertops without chipping them?

To cut through laminate countertops, you can use a hand saw, but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front.

To cut through laminate countertops, you can use a hand saw, but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front.

One may also ask, can I use a jigsaw to cut laminate countertop? Plastic laminate is surprisingly easy to cut. You can do it with a circular saw, a jigsaw, a router or even some hand tools. Cutting a sheet laminate by itself is best done with tin snips or aviation snips, provided you’re cutting it oversize and will trim it later.

Also to know, how do you cut laminate countertop sheets?

Tip: The utility knife method works best for cutting small pieces of Formica. For larger pieces, such as to cover an entire countertop, it is best to cut them roughly to size with a circular saw, then trim them with a router and sand down the edges. Drag the blade of a utility knife along the cut line to score it.

Will Home Depot cut laminate countertops?

Your local Home Depot store’s kitchen design center can partner with you to purchase and to cut the piece of countertop you’d like. You didn’t specify what material you’d like the countertop to made from (laminate, Corian, natural stone, etc.), so this can greatly affect the price and how it can be cut.

How do you put end caps on laminate countertops?

Cover the cut area with a laminate endcap that matches the surface of the laminate countertop. Place the countertop on a flat and stable work surface. Cover the exposed end of the countertop with a layer of wood glue. Brush a layer of contact adhesive over the buildup strip and the back of the laminate endcap.

Does IKEA cut countertops?

All of IKEA’s wooden countertops are pre-cut, which means you can take them home from the store.

What kind of jig saw blade to cut laminate countertop?

Therefore, you could use a table saw, a circular saw, a reciprocating saw or a jigsaw (ideal for curved cuts). As far as the blade is concerned, you should choose one with a fine high teeth count and long enough to cut trough the counter top (if it is also carbide tipped it would be great).

What is the best saw to cut a worktop?

The best tool for the job, which is almost impossible to do without, is a circular saw. As long as the blade is suitable for fine cuts and sharp then it shall cut through laminated chipboard or hardwood kitchen worktops like a hot knife through butter.

How can I cut my worktop without chipping?

Cut kitchen worktop. When cutting a kitchen worktop it is best if you cut it upside down, this is because the teeth on the blade cut on the way up, so there is much less chance of chipping the worktop. Some people draw a line on the worktop and then score it a few times using a sharp knife, then apply some masking tape

How do you cut a sink for a laminate countertop?

Cutting a Hole in a Countertop for the Sink Drill two starter holes in opposite corners just inside the cutting line. Use a 3/4-inch spade bit and drill through the laminate and substrate. Place the blade of the jigsaw in the starter hole and line up the blade exactly on the cutting line. Cut slowly along the line.

Can you cut laminate with a Dremel?

Plug the Dremel tool into a regular wall outlet and turn the power switch on to setting 15 so the multipurpose cutting bit will rotate at approximately 15,000 RPMs (rotations per minute), the recommended cutting speed for laminate flooring material.

Will Lowes cut countertop for you?

Tape the cut line and use a fine tooth blade. Look and see if there is not a company in your area that will cut the counter top for you. Sometimes they will take the Lowe’s countertop and cut it to your specifications. That will take the pressure off the contractor.

How much does a sheet of laminate cost?

Sheet laminate costs $30-$150 per sheet, depending on the size of the sheet and the color and style of the laminate.

Can you glue new laminate over old laminate countertops?

If you have Formica counters, but have decided that you prefer a new design, you can glue down new sheets of this trademarked laminate over the existing surface to give your kitchen a brand new look.